If at any time during the warranty period the product is determined to be defective or malfunctions, Honeywell shall repair or replace it at Honeywell's option. Temporary Bypass If you modify the temperature using the buttons when the thermostat is in programmable mode, the new temperature will be used for the next 2 hours. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. Configuration Menu n To access the configuration menu, press both buttons simultaneously for 3 seconds. This warranty shall not apply if it is shown by Honeywell that the defect or malfunction was caused by damage which occurred while the product was in the possession of a consumer. Warranty Honeywell warrants this product, excluding battery, to be free from defects in the workmanship or materials, under normal use and service, for a period of one 1 year from the date of purchase by the consumer. The setpoint for that mode flashes.
This warranty does not cover removal or reinstallation costs. Its digital display shows the temperature in degrees Fahrenheit or Celsius. After the batteries are installed, the thermostat performs a series of tests for approximately 5 seconds. For example, in the predefined energy-sav-ing schedule, periods 2 and 3 have been skipped for Saturday and Sunday. The schedule automatically controls your heating or cooling system by switching from one setpoint to the next according to the preset times. However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase.
Honeywell's sole responsibility shall be to repair or replace the product within the terms stated above. Heat-only and cool-only systems requiring a thermostat-activated fan relay connect to the thermostat with three wire strands, red, white or yellow, and green. Use this setting if you have a gas or fuel oil fur- nace. After replacing the batteries, readjust the time and day see section 5. This is a safety feature for Fan relay the compressor. This warranty shall not apply if it is shown by Honeywell that the defect or malfunction was caused by damage which occurred while the product was in the possession of a consumer. Thermostats Honeywell If this site has been useful for you please consider clicking on the button below making a small donation to keep it running.
However, the temperature and program settings are saved and do not need to be re-entered. Heat-only and cool-only connect to this thermostat model with either two or three wires, depending on whether or not the furnace requires a thermostat-activated fan relay. Heating and air-conditioning systems connect to this thermostat model with four wires; red, green, white and yellow colored wires. Warning: Before removing the batteries, place the system switch on the thermostat to Off. Using this energy-saving feature can automatically turn the system off when not needed and turn the system back on before the user returns. If the product is defective, i return it, with a bill of sale or other dated proof of purchase, to the place from which you purchased it, or ii call Honeywell Customer Care at 1-800-468-1502.
Slip the red-colored wire into the loose terminal and tighten the terminal screw. For each period, you can set the start time, the heating setpoint and the cooling setpoint. The thermostat will display the ambient temperature once it is installed on the wall. Note: This switch is not used if you have a 2-wireinstallation as the fan is not connected to the thermostat. Afterwards, the screen displays the actual temperature.
At the end of the bypass period, the thermostat returns to the temperature settings of the period currently underway. Cooling 82°F 28°C Note: To use the schedule, place the thermostat in programmable mode. If you want to quickly view the content of pages found on the following pages of the manual, you can use them. This warranty gives you specific legal rights, and you may have other rights which vary from state to state. We take no responsibility for the validity of the information available in each manual nor do we have any affiliation with the brands nor their products. At the end of the bypass period, the thermostat returns to the temperature settings of the period currently underway.
The four possible periods are: Wake up Leave for work Return home Sleep To see the default settings of each period, see section 5. Customer Assistance If you have any questions about the operation of your thermostat, please go to www. The settings for period 1 are displayed. Press for 3 seconds to select all 7 days. The setpoint is displayed for 5 seconds along with the icon. Advertisement Print version Many people prefer to read the documents not on the screen, but in the printed version. Note: To use the schedule, place the thermostat in programmable mode.
The jumper must be used in 3- or 4-wireinstallations if you wish to use the mode selector switch for the fan. Avoid draughty areas top of staircase, air outlet, etc. Help us bring this service to more people by placing a link to our page! Note: When you place the thermostat in Cooling mode, you might need to wait up to five minutes before cooling can start. The house icon flashes during the bypass. This is a safety feature for the compressor. Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation may not apply to you.
Rh Heating power supply Rc Cooling power supply W Heating signal Y Cooling signal G Fan Note: The red jumper wire between the Rc and Rh terminals must be removed in 2- or 5-wireinstallations. Note: When you place the thermostat in Cooling mode, you might need to wait up to five minutes before cooling can start. The icon dis- appears once the batteries are replaced. The house icon will disappear. I find it to be an easy setup. The house icon flashes during the bypass.