The power source must not exceed 30volts. If required use the external cable supplied to allow the radio to be installed further from the Controller Speaker Microphone. However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase. If you want to quickly view the content of pages found on the following pages of the manual, you can use them. How do I use the Key Lock function? If you wish to use the same Channel for normal communication, simply remove the Channel from Q mode. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual.
You can then release the whole faceplate from the radio quite easily. However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase. However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase. It would be used in an area where coverage was hindered by terrain, buildings or other environmental conditions. Summary of the content on the page No.
Your radio has 40 cha Summary of the content on the page No. If you need assistance setting up or using your Oricom product now or in the future, call Oricom Support. How do I restore the radio to factory settings? Carefully lever the faceplate out of the fixing at Position 1 positon 1 using a screwdriver. What radio install options do I have? Is this radio suitable for use outside of Australia? Always follow all information signs. Long range: With a massive 1 watt of power you can expect up to 7km range depending on terrain and environmental conditions. The range is longer when using the duplex feature. In setting 0, energy saving mode is switched off.
It is used when the radio signal needs to be magnified to get the desired distance coverage. For optimum performance your radio needs to be installed correctly. Transmitting Select the desired channel. At the same time gently pull the plug from the socket. If you hear static, the For example, channel is clear for use.
Press and hold button for 2 without using the headset. The Volume is set from level 1 to level 32. Puts the receiver in the Q mode. Ease the rubber boot out of the cable entry hole and slide it along the cable away from the front panel. A Low gain antenna will give you less range but wider coverage. It works by receiving a radio signal from one unit, magnifying it and retransmitting the signal to another radio unit.
Press the button five times. Select sensitivity level 1, 2 or 3 by using or. Inital power on channel will default to channel 12. These terms and conditions together. Oricom makes no other warranties or conditions, express or implied, including as to acceptable quality and fitness for a particular purpose, except as stated in this Warranty. If you have further questions about using the product after reviewing the resources above or would like to purchase replacement parts or accessories please call our Customer Support Team. Advertisement Print version Many people prefer to read the documents not on the screen, but in the printed version.
Select the repeater channel in your area channel 1 to channel 8. Press the menu button 4 times to enter duplex mode, press or to switch ensure that you do not interrupt other users already on the channel. A hissing noise will indicate an empty channel. It is good radio etiquette to monitor the channel for activity before you transmit, to 2. If the overvoltage warning appears, you must switch your radio off and disconnect it from the power source, before locating the cause of the trouble.
At the same time gently pull the plug from the socket see previous page. The power source must not exceed 30volts. Then press the required button. It is recommended that the Speaker Controller Microphone be left permanently connected to the radio, but if it must be disconnected, proceed as follows: 1. Oricom is not responsible for damage that occurs as a result of your failure to follow the instructions that came with the product.
Gently press the rubber boot into the hole surrounding the socket so that the slot around the boot fits neatly inside the rim of the entry hole. The black rubber washers are to be placed between the radio and mounting bracket to provide resistance to movement but still allow the position of the radio to be adjusted. Ensure radio is turned off. The radio has a high voltage input detection system, to warn you if an overvoltage situation occurs. Scan Removing the faceplate Rodger beep Battery level 1. Lift the rubber boot and the lip of the raised area on the front panel.